Instrutech Solutions

Industrial Flanges

Leading Exporters, Distributor, Wholesaler and Retailer of Blind Flange, Lap Joint Flange, Slip On Flange, Socket Weld Flange, Threaded Flange and Welding Neck Flange from Chennai.

Business Type Exporter, Supplier, Retailer, Wholesaler, Trader
Country of Origin India
Finishing Polished
Size (Inches) 10-20 Inch
Inner Diameter 10-20mm
Specialities Strong Construction, Fine Quality
Thickness 20-30mm
Packaging Type Wooden Boxes
Outer Diameter 30-50mm

Click to view more

Preferred Buyer From

Location Worldwide

Blind Flanges are manufactured without a bore and used to blank off the ends of piping, Valves and pressure vessel openings.

From the standpoint of internal pressure and bolt loading, blind flanges, particularly in the larger sizes, are the most highly stressed flange types.

However, most of these stresses are bending types near the center, and since there is no standard inside diameter, these flanges are suitable for higher pressure temperature applications.

Read More...


Yes! I am interested


Business Type Exporter, Supplier, Retailer, Wholesaler, Trader
Country of Origin India
Inner Diameter 10-20mm
Specialities Superior Finish, Strong Construction, Rust Proof, Fine Quality
Usage Industry Use
No. of Holes 4-8 Holes
Size 10-20 Inch
Packaging Type Shrink Wrapping, Bubble Wrapping
Finishing Polished

Click to view more

Preferred Buyer From

Location Worldwide

Lap Joint Flanges have all the same common dimensions as any other flange named on this page however it does not have a raised face, they used in conjunction with a "Lap Joint Stub End".

These flanges are nearly identical to a Slip On flange with the exception of a radius at the intersection of the flange face and the bore to accommodate the flanged portion of the Stub End.

Their pressure-holding ability is little, if any, better than that of Slip On flanges and the fatigue life for the assembly is only one tenth that of Welding Neck flanges.

They may be used at all pressures and are available in a full size range. These flanges slip over the pipe, and are not welded or otherwise fastened to it. Bolting pressure is transmitted to the gasket by the pressure of the flange against the back of the pipe lap (Stub End).

Lap Joint flanges have certain special advantages..

Freedom to swivel around the pipe facilitates the lining up of opposing flange bolt holes.

Lack of contact with the fluid in the pipe often permits the use of inexpensive carbon steel flanges with corrosion resistant pipe.

In systems which erode or corrode quickly, the flanges may be salvaged for re-use.

Read More...


Yes! I am interested


Business Type Exporter, Supplier, Retailer, Wholesaler, Trader
Country of Origin India
Shape Round
Flange Type Slip On
Inner Diameter 10-20mm
Outer Diameter 30-50mm
Specialities Strong Construction, Rust Proof, Fine Quality

Preferred Buyer From

Location Worldwide

The calculated strength from a Slip On flange under internal pressure is of the order of two-thirds that of Welding Neck flanges, and their life under fatigue is about one-third that of the latter.

The connection with the pipe is done with 2 fillet welds, as well at the outside as also at the inside of the flange.

The X measure on the image, are approximately..
Wall thickness of pipe + 3 mm.

This space is necessary, to do not damage the flange face, during the welding process.

A disadvantage of the flange is, that principle always firstly a pipe must be welded and then just a fitting. A combination of flange and elbow or flange and tee is not possible, because named fittings have not a straight end, that complete slid in the Slip On flange.

Read More...


Yes! I am interested


Business Type Exporter, Supplier, Retailer, Wholesaler, Trader
Country of Origin India
Material Metal
Diameter 10-20mm
Shape Round
Thickness 10-20mm
Application Industrial Fitting
Feature Perfect Shape, High Strength, Fine Finishing, Excellent Quality
Finishing Polished

Click to view more

Preferred Buyer From

Location Worldwide

Socket Weld flanges were initially developed for use on small-size high pressure piping. Their static strength is equal to Slip On flanges, but their fatigue strength 50% greater than double-welded Slip On flanges.

The connection with the pipe is done with 1 fillet weld, at the outside of the flange. But before welding, a space must be created between flange or fitting and pipe.

ASME B31.1 1998 127.3 Preparation for Welding (E) Socket Weld Assembly says..
In assembly of the joint before welding, the pipe or tube shall be inserted into the socket to the maximum depth and then withdrawn approximately 1/16" (1.6 mm) away from contact between the end of the pipe and the shoulder of the socket.

The purpose for the bottoming clearance in a Socket Weld is usually to reduce the residual stress at the root of the weld that could occur during solidification of the weld metal. The image shows you the X measure for the expansion gap.

The disadvantage of this flange is right the gap, that must be made. By corrosive products, and mainly in stainless steel pipe systems, the crack between pipe and flange can give corrosion problems. In some processes this flange is also not allowed. I am not an expert in this matter, but on the internet, you will find a lot of information about forms of corrosion.

Read More...


Yes! I am interested


Business Type Exporter, Supplier, Retailer, Wholesaler, Trader
Country of Origin India
Inner Diameter 10-20mm
Outer Diameter 30-50mm
Specialities Superior Finish, Strong Construction, High Strength, Fine Quality
Packaging Type Shrink Wrapping, Jute Wrapping
Thickness 10-20mm
Finishing Polished

Preferred Buyer From

Location Worldwide

Threaded Flanges are used for special circumstances with their main advantage being that they can be attached to the pipe without welding. Sometimes a seal weld is also used in conjunction with the threaded connection.

Although still available in most sizes and pressure ratings, screwed fittings today are used almost exclusively in smaller pipe sizes.

A threaded flange or fitting is not suitable for a pipe system with thin wall thickness, because cutting thread on a pipe is not possible. Thus, thicker wall thickness must be chosen.

ASME B31.3 Piping Guide says..
Where steel pipe is threaded and used for steam service above 250 psi or for water service above 100 psi with water temperatures above 220° F, the pipe shall be seamless and have a thickness at least equal to schedule 80 of ASME B36.10.

Read More...


Yes! I am interested


Business Type Exporter, Supplier, Retailer, Wholesaler, Trader
Country of Origin India
Finishing Polished
Size (Inches) 10-20 Inch
Inner Diameter 10-20mm
No. of Holes 4-8 Holes
Specialities Strong Construction, Rust Proof, Fine Quality, Durable
Thickness 10-20mm
Outer Diameter 30-50mm

Click to view more

Preferred Buyer From

Location Worldwide

Welding Neck Flanges are easy to recognize at the long tapered hub, that goes gradually over to the wall thickness from a pipe or fitting.

The long tapered hub provides an important reinforcement for use in several applications involving high pressure, sub-zero and / or elevated temperatures. The smooth transition from flange thickness to pipe or fitting wall thickness effected by the taper is extremely beneficial, under conditions of repeated bending, caused by line expansion or other variable forces.

These flanges are bored to match the inside diameter of the mating pipe or fitting so there will be no restriction of product flow. This prevents turbulence at the joint and reduces erosion. They also provide excellent stress distribution through the tapered hub and are easily radiographed for flaw detection.

Read More...


Yes! I am interested




Looking for Product Name ?

Close

Raise your Query

Hi! Simply click below and type your query.

Our experts will reply you very soon.

WhatsApp Us